BMW Multi-Color Halo Angel Eyes Installation Instructions

Installing Tips:

1) Inspect and test your kit prior to installing. We test every product before it goes out our door. You should be good to go! If any thing is not working, best to contact us before taking your headlights apart.

2) Have a beer waiting for you at the end to celebrate. 

3) These Multi-Color Kits use an RF (RADIO FREQUENCY) wireless remote, we recommend you place the RF receiver (RGB Control Box) near the front grille so you can stand in front of the car using the remote control. Also Install RF Receiver (RGB Control Box) away from heat of engine. NOTE: These are RGB rings, the white color is mixed with Red + Green + Blue, therefore it is not exact "White" like our single color 7000k white LED Halo-Angel Eye kits.

Tools Required: Phillips Screw Driver (corner lamps) • Flat Head Screw Driver (optional for headlight cover) • Pliers (handy to have) • Electrical Tape • 10mm Socket or Adjustable Wrench (ground nut, coolant reservoirs, positive battery terminal) • T25 Torx Bit (ECU box cover)

The following steps to installing Kit and removing Headlight Cover:

You can Download "steps to removing your BMW headlight assembly and installing multi-color halo-angel eye rings guide"


1. Open your hood and we'll start the Headlight Lens removal:

2. Using a Phillips head screw driver, place the tip in the hole of the top fender, push down tab inside to release the corner lamp assembly. You'll see the corner lamp move slightly forward. Pull the lamp assembly forward and away and allow to hang freely to the side of the vehicle. Just to get the corner lamp out of the way, check position of bulb harness before disconnecting the wiring harness and twist counter clockwise to disconnect. Checking reassures you to know the correct position in twisting bulb harness back together.

3. Black Rubber Trim: Lift up the five (3 on top and 2 on side) tabs and pull the trim towards you from the headlight.

4. Remove the bottom body trim away from beneath the headlight. Pull towards you from the inside and it's hinged on the outer section near the corner lamp. You can leave hanging out of the way. Continue...

13 - 13 of 13 items
Sort By:
13 - 13 of 13 items

5. Clear Headlight Lens removal: With you fingers release the seven (7 black tabs) that hold the lens assembly. Pull with both hands straight towards you to remove the lens.

6. Bezel Trim: Release the seven (7) clips that hold the bezel to the headlight. Pull with both hands straight towards you to remove the bezel.

7. Using the supplied hardware clear clips, attach two to the rings and mount it to the correct headlight size, level your Halo-Angel Eyes straight (top-bottom and left-right). 

Optional: to make more room you can easily remove the four (4) plastic clips that hold the intake duct assembly in place and remove.

8. Remove the high beam H7 bulb and peel back the rubber insulator.

9. Make sure wires wont be visible from the front. Guide the wires from the rings in the headlight assembly through the opening of where the H7 bulb goes. A small incision may have to be made to allow room for the wires. Pull the wires through with pliers or your fingers. 

10. Connect and click the RGB Controller to the Multi-Color Halo-Angel Eye connectors matching Arrows indicated on connectors.

11. Remove the four (4) T25 Torx screws to remove the cover of the ECU box.

12. Route the wiring from the drivers side angel eyes along with OEM wiring on the right drivers-side chassis.

13. Inside ECU box: Using Wire Tap Connectors, Tap the RED wire from the RGB Control Box to the Red-White stripe-Yellow/Gold stripes wire in the wiring loom. This will allow your kit to function by turning on or off your ignition. Connect black wire to any metal (UNPAINTED) bolt for ground. Option: to tap the corner lamps to function with corner lamps.

14. To reinstall, do steps in reverse from 11-2. The corner lamps just slide right back in with a click.

15. Crank up your Bimmer and Wholaaa, time to grab that beer!